Heb in mijn computer een Dual-Chanal geheugen zitten van TwinMoss 1024 mb, nu is de memory -clock in de bios ingesteld op 200 mhz ,dat is waarop het geheugen kan draaien,maar in CPU-Z geeft hij maar 133,3 Mhz aan ,hoe kan ik dit veranderen.
Geheugen probleem
- Onderwerp starter a.veldman
- Startdatum
- Status
virtuosa
Meubilair
- Lid geworden
- 17 aug 2001
- Berichten
- 5.300
welk moederbord is het eigelijk
bij mij lanparty moet ik beginnen met bank 2 van elk als ik het in de eerste bank doe werkt,
het ook alleen op 333.
kijk voor meer informatie in de handleiding van het bord.
of begin eens ook met eerst het vullen van bank 2
bij mij lanparty moet ik beginnen met bank 2 van elk als ik het in de eerste bank doe werkt,
het ook alleen op 333.
kijk voor meer informatie in de handleiding van het bord.
of begin eens ook met eerst het vullen van bank 2
casepimper
Gebruiker
- Lid geworden
- 17 feb 2006
- Berichten
- 87
dit is wat er in de manual stond
2.3 Installation of Memory Modules (DIMM)
939Dual-SATA2 motherboard provides four 184-pin DDR (Double Data Rate)
DIMM slots, and supports Dual Channel Memory Technology. For dual channel
configuration, you always need to install identical (the same brand, speed,
size and chip-type) DDR DIMM pair in the slots of the same color. In other words,
you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and
DDR2; Blue slots; see p.8 No.7) or identical DDR DIMM pair in Dual Channel B
(DDR3 and DDR4; Black slots; see p.8 No.8), so that Dual Channel Memory
Technology can be activated. This motherboard also allows you to install four
DDR DIMMs for dual channel configuration, and please install identical DDR
DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration
Table below.
* For the configuration (3), please install identical DDR DIMMs in all four slots.
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of blue slots
(DDR1 and DDR2), or in the set of black slots (DDR3 and DDR4).
2. If only one memory module or three memory modules are installed
in the DDR DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDR1
and DDR3, it is unable to activate the Dual Channel Memory Technology
.
en dit is wat er in de bios aangepast kan worden
Memory Clock
This item can be set by the code using [Auto]. You can set one of the
standard values as listed: [133 MHz (DDR266)], [166 MHz (DDR333)],
[200 MHz (DDR400)].
kijk of je hier wat mee kan succes:thumb:
2.3 Installation of Memory Modules (DIMM)
939Dual-SATA2 motherboard provides four 184-pin DDR (Double Data Rate)
DIMM slots, and supports Dual Channel Memory Technology. For dual channel
configuration, you always need to install identical (the same brand, speed,
size and chip-type) DDR DIMM pair in the slots of the same color. In other words,
you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and
DDR2; Blue slots; see p.8 No.7) or identical DDR DIMM pair in Dual Channel B
(DDR3 and DDR4; Black slots; see p.8 No.8), so that Dual Channel Memory
Technology can be activated. This motherboard also allows you to install four
DDR DIMMs for dual channel configuration, and please install identical DDR
DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration
Table below.
* For the configuration (3), please install identical DDR DIMMs in all four slots.
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of blue slots
(DDR1 and DDR2), or in the set of black slots (DDR3 and DDR4).
2. If only one memory module or three memory modules are installed
in the DDR DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDR1
and DDR3, it is unable to activate the Dual Channel Memory Technology
.
en dit is wat er in de bios aangepast kan worden
Memory Clock
This item can be set by the code using [Auto]. You can set one of the
standard values as listed: [133 MHz (DDR266)], [166 MHz (DDR333)],
[200 MHz (DDR400)].
kijk of je hier wat mee kan succes:thumb:
- Status
