Kosko
Gebruiker
- Lid geworden
- 28 feb 2005
- Berichten
- 57
Ik heb sinds een tijdje een nieuwe harde schijf :seagate 320gb sata2 16mb
en als ik naar deze schijf ga in deze comp. dan druk ik er op en dan opent ie de schijf maar dan krijg ik een lege schijf volgens de windows verkenner terwijl er wel wat op staat, als ik dan op vorige druk en dan weer die schijf aan klik en open dan doet ie het in eens weer wel
ik vond een functie bij speedfan 4.29 dat je je hardeschijf kan checken
s.m.a.r.t. heet het en als ik dan via internet hem uitlees krijg ik dit:
Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute ****h, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a ST3320620AS with firmware 3.AAD.
The average temperature for this hard disk is 38C (MIN=30C MAX=48C) and yours is 34C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Your hard disk is now being compared to real data used to define normal values for your specific hard disk model. This way, the analysis can automatically use proper operating ranges. The images give you an idea of how each attribute is within such range. Current and raw values are shown for easier reference for experienced users. There are 1166 hard disk models in the current archive.
Attribute Current Raw Overall
9 Raw Read Error Rate 115 89837854 Very good
10 Spin Up Time 96 0 Very good
10 Start/Stop Count 100 96 Very good
10 Reallocated Sector Count 100 0 Very good
4 Seek Error Rate 73 22487740 Good
10 Power On Hours Count 100 456 Very good
10 Spin Retry Count 100 0 Very good
10 Power Cycle Count 100 118 Very good
10 Unknown attribute 187 100 0 Very good
10 Unknown attribute 189 100 0 Very good
9 Unknown attribute 190 66 589299746 Very good
0 Hardware ECC Recovered 62 189543734 Watch
Warning: Hardware ECC Recovered is below the average limits (64-98).
10 Current Pending Sector 100 0 Very good
10 Offline Uncorrectable Sector Count 100 0 Very good
10 Ultra DMA CRC Error Rate 200 0 Very good
10 Write Error Rate 100 0 Very good
10 TA Increase Count 100 0 Very good
NOTE: not all warnings are reflected on fitness and performance overall values as relevancy is based upon the settings from the hard disk manufacturer who is the best entity deputed to define such relationships.
The overall fitness for this drive is 96%.
The overall performance for this drive is 96%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
Heeft iemand enig idee wat dit kan zijn, of ervaring mee.
anders kan ik hem namelijk RMA'en
Alvast bedankt
Jasper
en als ik naar deze schijf ga in deze comp. dan druk ik er op en dan opent ie de schijf maar dan krijg ik een lege schijf volgens de windows verkenner terwijl er wel wat op staat, als ik dan op vorige druk en dan weer die schijf aan klik en open dan doet ie het in eens weer wel
ik vond een functie bij speedfan 4.29 dat je je hardeschijf kan checken
s.m.a.r.t. heet het en als ik dan via internet hem uitlees krijg ik dit:
Almost every EIDE or SATA hard disk includes S.M.A.R.T. data. That information is collected by the drive itself and contains data that the manufacturer considered relevant to check reliability. The data is made up of several attributes that have a current value, a worst one, a threshold, some raw data, and some flags. Basically, when any attribute's current value is below its threshold, the hard disk is considered unreliable and likely to fail. By using several techniques, this report tries to give a wider range of info, basing its analysis on advanced comparisons with normal values based on real hard disks and on expert-like checks. The final results are not to be taken as an absolute ****h, but they are a very good approach to what a professional would say about your hard disk status.
Your hard disk is a ST3320620AS with firmware 3.AAD.
The average temperature for this hard disk is 38C (MIN=30C MAX=48C) and yours is 34C.
Your hard disk's S.M.A.R.T. attributes are now being analyzed and a full report about the reliability, health and status of your hard disk is generated:
Your hard disk is not below any attribute threshold. This is good.
Your hard disk was never below any attribute threshold. This is good.
Your hard disk is now being compared to real data used to define normal values for your specific hard disk model. This way, the analysis can automatically use proper operating ranges. The images give you an idea of how each attribute is within such range. Current and raw values are shown for easier reference for experienced users. There are 1166 hard disk models in the current archive.
Attribute Current Raw Overall
9 Raw Read Error Rate 115 89837854 Very good
10 Spin Up Time 96 0 Very good
10 Start/Stop Count 100 96 Very good
10 Reallocated Sector Count 100 0 Very good
4 Seek Error Rate 73 22487740 Good
10 Power On Hours Count 100 456 Very good
10 Spin Retry Count 100 0 Very good
10 Power Cycle Count 100 118 Very good
10 Unknown attribute 187 100 0 Very good
10 Unknown attribute 189 100 0 Very good
9 Unknown attribute 190 66 589299746 Very good
0 Hardware ECC Recovered 62 189543734 Watch
Warning: Hardware ECC Recovered is below the average limits (64-98).
10 Current Pending Sector 100 0 Very good
10 Offline Uncorrectable Sector Count 100 0 Very good
10 Ultra DMA CRC Error Rate 200 0 Very good
10 Write Error Rate 100 0 Very good
10 TA Increase Count 100 0 Very good
NOTE: not all warnings are reflected on fitness and performance overall values as relevancy is based upon the settings from the hard disk manufacturer who is the best entity deputed to define such relationships.
The overall fitness for this drive is 96%.
The overall performance for this drive is 96%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
Heeft iemand enig idee wat dit kan zijn, of ervaring mee.
anders kan ik hem namelijk RMA'en
Alvast bedankt
Jasper
