welk geheugen
- Onderwerp starter coolkil
- Startdatum
- Status
frankwannet
Inventaris
- Lid geworden
- 6 jun 2006
- Berichten
- 26.479
Hoi..
Draai de scan eens en wellicht krijg je iets voorgeschoteldt.
http://www.crucial.com/systemscanner/index.aspx
Draai de scan eens en wellicht krijg je iets voorgeschoteldt.
http://www.crucial.com/systemscanner/index.aspx
frankwannet
Inventaris
- Lid geworden
- 6 jun 2006
- Berichten
- 26.479
ok....na ja de gegevens staan er eigenlijk al.En ik zie geen problemen met jou voorgestelde geheugen.Met pc wizard zou je nog het juiste type van het bord wellicht kunnen vinden.Aan de hand daarvan kunnen we weer eens verder kijken wat er nog mogelijk is.
frankwannet
Inventaris
- Lid geworden
- 6 jun 2006
- Berichten
- 26.479
Ohh..als jij reepje al in bezit heb dan plaatsen en proberen.Is het niet goed dan krijg je vanzelf een piep of geen opstart.
Palomino
Terugkerende gebruiker
- Lid geworden
- 30 dec 2006
- Berichten
- 3.043
Dit stond in de gebruiksaanwijzing:
For proper system operation, if the computer supports DDR-SDRAM DIMMs, the DIMMs must
be industry-standard 184-pin, unbuffered PC2700 333 MHz- or PC3200 400 MHz-compliant,
2.5 volt DDR-SDRAM DIMMs. The DDR-SDRAM DIMMs must also:
■support CAS latency 2.5 or 3 (CL = 2.5 or CL=3)
■contain the mandatory JEDEC SPD information
In addition, the computer supports:
■128Mbit, 256Mbit, and 512Mbit non-ECC memory technologies
■single-sided and double-sided DIMMS
■DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not supported
The following processor bus frequencies are required for the system to run at the supported
memory frequencies.
If a memory frequency is paired with an unsupported processor bus frequency, the system will
run at the highest supported memory speed. For example, if a 333 MHz DIMM is paired with a
400 MHz processor bus, the system will run at 266 MHz, the highest supported memory speed.
✎
The system will not start if you install unsupported DIMMs.
Memory Frequency Required Processor Bus Frequency
266 MHz 400 MHz, 533 MHz, or 800 MHz
333 MHz 533 MHz or 800 MHz
400 MHz 800 MHz
For proper system operation, if the computer supports DDR-SDRAM DIMMs, the DIMMs must
be industry-standard 184-pin, unbuffered PC2700 333 MHz- or PC3200 400 MHz-compliant,
2.5 volt DDR-SDRAM DIMMs. The DDR-SDRAM DIMMs must also:
■support CAS latency 2.5 or 3 (CL = 2.5 or CL=3)
■contain the mandatory JEDEC SPD information
In addition, the computer supports:
■128Mbit, 256Mbit, and 512Mbit non-ECC memory technologies
■single-sided and double-sided DIMMS
■DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not supported
The following processor bus frequencies are required for the system to run at the supported
memory frequencies.
If a memory frequency is paired with an unsupported processor bus frequency, the system will
run at the highest supported memory speed. For example, if a 333 MHz DIMM is paired with a
400 MHz processor bus, the system will run at 266 MHz, the highest supported memory speed.
✎
The system will not start if you install unsupported DIMMs.
Memory Frequency Required Processor Bus Frequency
266 MHz 400 MHz, 533 MHz, or 800 MHz
333 MHz 533 MHz or 800 MHz
400 MHz 800 MHz
frankwannet
Inventaris
- Lid geworden
- 6 jun 2006
- Berichten
- 26.479
Okidoki
Succes:thumb:
Succes:thumb:
- Status
