Hitachi Deskstar en Asus P4PE

Status
Niet open voor verdere reacties.

Jannet

Gebruiker
Lid geworden
11 dec 2000
Berichten
78
Ik heb een Asus P4PE moederbord, geschikt voor SATA.
Daarin hangt een Maxtor IDE schijf met Windows XP Prof.

De schijf was zowat vol, dus kocht ik van de week een Hitachi Deskstar T7K250 250 GB Sata 7200 rpm.
Ik sloot 'm aan op de SATA-poort. Zette de SATA/IDE Raid controller in het BIOS op enabled. Installeerde vanaf de cdrom van het moederbord de Promise Fast track 376 controller.

In apparaatbeheer zag ik nu dat er een SCSI device was bijgekomen. Bij deze computer zag ik de schijf niet.
Vervolgens heb ik de computer opnieuw opgestart en in het Raid menu heb ik de schijf automatisch laten detecteren. Hij werd gedetecteerd als Promise 1+0 Stripe/Raid0. Zo staat hij nu in apparaatbeheer. Bij "deze computer" is hij zichtbaar als lokaal station J.

Ik wil de schijf echter niet in een Raid configuratie. Ik wil hem als primaire schijf en daar het besturingssysteem op installeren. Dat gaat echter niet want hij wordt niet in het BIOS gezien. En als ik van CDROM boot om windows te installeren en ik druk op F6 dan geeft hij zodra de floppy is benaderd de foutmelding the file\winxp\fasttx2k.sys could not be loaded. Error code 18.

Wat doe ik fout?

Jan
 
The promise fasttrack

Die controler is zover ik weet van de raid drive. Als het goed is heb je een extra IDE connector (drie dus in totaal). Daarnaast ook nog 2 sata raid connectors.

De sata had een andere driver en twee andere conectors, en wordt zover ik weet vanzelf herkend door Windows (niet 98 of ME), omdat hij op de southbrige zit.

Heb je al in schijbeheer gekeken, mogelijk moet je hem nog aanmelden.

Overigens moet in je bios SATA wel op enabled staan.

Eric.
 
Beste Eric,

bedankt voor je reactie.

Ik heb 2 IDE connectors (Ultra DMA 100/66) en 2 Serial Ata connectors (7-pin Pri SATA1, Sec SATA1).

Als ik de SATA schijf aansluit op 1 van de 2 sata connectors dan ziet windows deze (uiteraard) niet. Zodra ik nu deonboard SATA/IDE Raid controller op enabled zet. dan detecteert windows de raid controller en de schijf en vraagt naar de cdrom met de Promise Fast track controller. Hij wordt automatisch in de 0+1/raid0 geplaatst.
In schijfbeheer is hij zichtbaar als J-schijf. Ook bij Deze Computer is hij dan als J-schijf zichtbaar. Hoe krijg ik hem nou uit die raid?
Ik wil hem gewoon als primaire schijf gebruiken en daar windows op installeren. Heb ik hem goed aangesloten?

Jan
 
Sorry

Had het niet goed begrepen.

Ok mijn asus, waarvan ik dacht dat die bijna hetzelde was had er meer, maar dat maakt niet uit.

Latere versies hebben inderdaad maar 1 driver.

Als je Windows op die drive wilt zetten, moet je een flop maken. Meestal zit er op de CD iets als make boot of gewoon alle files in een map.

Je moet zoeken naar TxtSetup.oem.

Als je een flop formateerd (zonder /s) kun je alle files daarop kwijt.

Je doet je Windows CD in de drive en start opnieuw op.
Mischien moet je boot sequence even aanpassen.

Als hij gaat laden druk je op [F6] en na een tijdje vraagt hij dan of je een driver wilt installeren, je drukt op [E] en hij zal op de flop naar die txtsetup.oem zoeken.

Als je nog vragen hebt hoor ik het wel.

Eric.:thumb:
 
Hoi Eric,

Ik heb een flop gemaakt en daar de driver opgezet:

txtsetup.oem
fasttx2k
fasttx2k.systemfile
fasttx2k.beveiligingscatalogus
fasttx2k.setupgegevens

zit nog een textfile bij:

Installing Driver During New Windows XP Installation

Note: Before install, you must make a "Promise Floppy Install DISK".
To copy all files and folders in {CD-ROM Drive}:\Drivers\Promise\*.* to Floppy.

1a. Floppy Install: Boot the computer with the Windows XP installation diskettes.
1b. Floppyless Install: Boot from floppy and type "WINXP". After files have been copied,
the system will reboot. On the reboot, press <F6> after the message
"Setup is inspecting your computer's hardware configuration..." appears.
1c. CD-ROM Install: Boot from the CD-ROM. Press <F6> after the message
"Press F6 if you need to install third party SCSI or RAID driver" appears.
2. When the "Windows XP Setup" window is generated, press "S" to Specify an Additional
Device(s) and press the "Enter" key.
3. Insert the "Promise Floppy Install DISK" into the Floppy Drive: and press "Enter" key.
4. Choose "WINXP Promise FastTrak 376 (tm) Controller" from the list that appears on screen,
then press the "Enter" key.
5. The Windows XP Setup screen will appear again saying
"Setup will load support for the following mass storage devices:"
The list will include "WINXP Promise FastTrak 376 (tm) controller"..
NOTE: If you need to specify any additional devices to be installed, do so at this time.
Once all devices are specified, continue to step 7.
6. From the Windows XP Setup screen, press the Enter key. Setup will now load all device
files and then continue the Windows XP installation.

Als ik al deze files naar een floppy kopieer en ik voer de door jou aangegeven procedure uit (is zelfde als in textfile). Dan krijg ik na de selectie van de WINXP promise fast treack controller de foutmelding die ik onderaan in mijn eerst bericht heb vermeld.

Ik kan bij Asus ook geen recentere driver vinden. Kun jij aan de foutmelding zien, wat er misgaat?

Jan
 
Kan het aan je flop liggen

Kijk eens of je het bestand van de flop kunt openen in kladblok.

Wat je tezien krijgt zal je niets zeggen. maar het gaat er om dat je flop gelezen kan worden.

Als hij gaat harken, even een andere flop nemen of hem opnieuw formatteren en het zaakje er weer op zetten.

Eric.
 
Laatst bewerkt:
De bestanden zijn in kladblok te lezen. De flop hapert niet.

Nog eens geprobeerd, maar foutmelding File\winxp\fasttx2k.sys could not be loaded, error code 18 blijft.

Nog andere suggesties?

Groet,

Jan
 
Ogenblikje

Het lijkt er op dat:

Of de txtsetup.oem is niet goed.
Of je hebt zomaar de bestanden gekopieerd.

Hij zegt dat hij niet kon laden.
\winxp\fasttx2k.sys could not be loaded

Dus hij verwacht fastx2k.sys niet in de root, maar in een map WinXP.

Heb jij een map WinXP op je flop ?

Eric.
 
Hoi Eric,

Ik heb geen map WinXP op mijn flop. Op de CDrom bevindt zich een map Promise en daarin zit naast een map win98, win nt e.d ook een map WinXp met daarin de bestanden die ik noemde. In de (hoofd) map promise bevindt zich het bestand txtsetup.oem en fasttx2k. Deze 2 bestanden plus degene die in het mapje XP staan heb ik naar de flop gekopieerd.
Hier doe ik het blijkbaar niet goed?


Jan
 
Nee dat klopt

Je moet de hele handel (de inhoud van de map Promise) kopiëren. Dus met de mappen.

De map 98 en NT hoeft natuurlijk niet, want daar zal hij niet zoeken.

Eric.

P.S. Je merkt vanzelf wel als hij iets niet kan vinden.
 
Laatst bewerkt:
Dag Eric,

Daar ben ik weer. Ik heb de hele map Promise naar de flop gekopieerd. Nu geeft hij aan dat hij het bestand txtsetup.oem niet kan vinden. Deze staat wel degelijk in de map. Hij komt nu dus eigenlijk minder ver, dan wanneer ik de bestanden los op de flop zet, want dan kan hij txtsetup.oem wel vinden en kan ik uit de lijst de driver kiezen. Hij loopt dan echter vast op fasttx2k.sys die hij niet kan laden.

Wat denk jij?

Jan
 
zet ze op de volgende manier op de flop:

a:\Txtsetup.oem
a:\fasttx2k
a:\winxp\fasttx2k
a:\winxp\fasttx2k.sys
a:\winxp\fasttx2k.cat
a:\winxp\fasttx2k.ini

van die fasttx2k weet in het niet zeker waardie inhoord maar als je ze zo neerzet zou hij moeten werken...
 
Laatst bewerkt:
Ik heb het gedaan zoals jij aangaf. Ik heb alleen de file fasttx.2k rechtstreeks onder a gezet en niet ook nog eens in de windowsmap, omdat hij op de cd ook niet in de windowsmap staat.

Hij geeft nu na de selectie van de driver uit een menuutje aan dat de file winxp\fasttx2k.sys niet geladen kan worden. Error code 4096. Dat is dus weer anders dan errorcode 18.

Jan
 
Dit zo gedaan ?

Installing Driver in Existing Windows XP System

WARNING: If you will be moving the boot drive containing the existing Windows XP operating
system to a mirrored RAID 1 array on the FastTrak 376 , the FastTrak 376 driver MUST be loaded
to the hard drive while it is still attached to your existing hard drive controller.
Do not attach this drive or any other hard drive to the FastTrak 376 controller before completing
this step.

After installing the FastTrak 376 and rebooting your system, Windows XP setup will show a
"New Hardware Found" dialog box. Under Windows XP, the "PCI RAID Controller" will be displayed.

1. Choose "INSTALL FROM A LIST OR SPECIFIC LOCATION" then press "NEXT".
2. Choose "SEARCH FOR THE BEST DRIVER IN THESE LOCATION" and
choose "INCLUDE THIS LOCATION IN THE SEARCH" then
Type "CD-ROM Drive:\Drivers\Promise\WINXP\" in the text box. Press "NEXT".
3. The Windows XP Setup screen will appear again saying
"Setup will load support for the following mass storage devices
-WIN XP Promise FastTrak 376 (tm) controller". The FastTrak 376 driver
will now be copied on to the system and entered into the Windows XP driver database.
4. Finally, Windows XP will then restart for the driver installation.

Installing Driver During New Windows XP Installation
1a. Floppy Install: Boot the computer with the Windows XP installation diskettes.
1b. Floppyless Install: Boot from floppy and type "WINXP". After files have been copied,
the system will reboot. On the reboot, press <F6> after the message
"Setup is inspecting your computer's hardware configuration..." appears.
1c. CD-ROM Install: Boot from the CD-ROM. Press <F6> after the message
"Press F6 if you need to install third party SCSI or RAID driver" appears.
2. When the "Windows XP Setup" window is generated, press "S" to Specify an Additional
Device(s)
3. Press "O" to select "Other" and press the "Enter" key.
4. Insert the Promise Technology driver into the CD-ROM Drive: and press "Enter" key.
5. Choose "WINXP Promise FastTrak 376 (tm) Controller" from the list that appears on screen,
then press the "Enter" key.
6. The Windows XP Setup screen will appear again saying
"Setup will load support for the following mass storage devices:"
The list will include "WINXP Promise FastTrak 376 (tm) controller"..
NOTE: If you need to specify any additional devices to be installed, do so at this time.
Once all devices are specified, continue to step 7.
7. From the Windows XP Setup screen, press the Enter key. Setup will now load all device
files and then continue the Windows XP installation.


Confirming Windows XP Installation
1. From Windows XP, open the Control Panel from "My Computer" followed by the System icon.
2. Choose the "Hardware" tab, then click the "Device Manager" tab.
3. Click the "+" in front of "SCSI & RAID Controllers hardware type."
The driver "WINXP Promise FastTrak 376 (tm) Controller" should appear.
 
@ bandit

Als ik het goed begrijp wil hij een nieuwe instal doen op die drive.

Eric.
 
Ik heb de driver eens geinstalleerd in de bestaande Xp configuratie, maar dan niet van cdrom maar van diskette. Dit ging niet geheel vlekkeloos. Ik moest tot 2x toe opnieuw opdracht geven, omdat hij fasttx2k.sys niet uit die windowsmap kon halen. Uiteindelijk deed hij het wel zonder dat ik een wijziging hoefde aan te brengen.
Met de geinstalleerde driver heb ik vervolgens opnieuw geboot van cdrom. Nu laadde hij wel. In de setup werd de nieuwe schijf zichtbaar. Deze geselecteerd om het besturingssysteem op te installeren. Vervolgens opdracht gegeven om de schijf als NTFS te formatteren. Toen dat klaar was wilde hij fasttx.2k.sys laden, maar dat kon hij wederom niet. Heb installatieproces toen maar weer afgebroken na verschilende keren geprobeerd te hebben dit bestand te laden.
Zit niet mee, maar we zijn al iets verder.

Jan
 
Maar!

Staat hij wel in je bios op enabled ??

Eric.

P.S. Bij mijn shutlle is het ook. Ik dacht, ik heb geen raid, dus zette hem op disabled. Maar toen zag hij zijn SATA schijf niet meer.
 
Status
Niet open voor verdere reacties.
Terug
Bovenaan Onderaan