Hoi,
Ik heb een ide raid controllertje aangeschaft. Ik wil hier 2 x 250 gb hd's op aansluiten
in raid 1 (mirror). Nu lees ik verschillende verhalen dat de info van de harddisk verwijderd wordt indien deze aangesloten worden en de harde schijven gemount worden.
In de handleiding echter staat een stuk over het installeren van de raid controller op een reeds geinstalleerd systeem. Hierin staat niets over data verlies oid.
dit is het stuk uit de handleiding:
Silicon Image Ultra-133 Medley ATA Raid Controller OS Driver Installation
-------------------------------------------------------------------------
---------------------------------------------------------------------------
3)Adding the SiI RAID controller to an existing Windows 2000/XP installation
---------------------------------------------------------------------------
Follow the instructions in this section to install the Silicon Image
SiI 680 driver on a system already running Windows 2000.
1. Power off the system. Connect the hard drives to the PCI-680
controller and insert the controller into a PCI slot. Power up
the system.
2. During OS boot up, Windows 2000 will display the
'Found New Hardware Wizard'. Click 'Next'.
3. Select 'Search for a suitable driver for my device
(Recommended)' and Click 'Next'.
4. Under 'Optional search locations' insure that 'Floppy disk drives'
is checked.
5. Insert the diskette labeled ' Silicon Image Ultra-133 Medley ATA Raid Driver
Installation Disk' into A: and click 'Next'.
6. When the wizard indicates that it found a driver for the device click
'Next'.
7. If the 'Digital Signature Not Found' dialog appears, click 'Yes' to
continue installing the driver.
8. The wizard will now copy the required files to the system and start the
driver. After starting the driver the wizard will display a completion
dialog, click 'Finish' to exit the wizard.
9. See instructions in section 4 to verify controller was installed
correctly.
------------------------------------------------------------------
4) Verifying controller installation under Windows NT, 2000 and XP
------------------------------------------------------------------
Follow the instructions in this section to verify that the controller was
installed correctly.
For Windows 2000/XP
1. Right click on 'My Computer' icon, select 'Properties',
left click on 'Hardware' tab, and then on 'Device Manager'
button.
2. Double click on 'SCSI and RAID Controllers', If there is no
yellow '! ' or ' ? ' in front of
'Silicon Image Ultra-133 Medley ATA Raid Controller', the driver
is started correctly.
3. To view information about the devices attached to the controller, use the SiICfg
Utility and click on the device from the list.
For Windows NT 4.0
1. Double click on 'My Computer' icon, select 'Control Panel', click
on 'SCSI Adapters' icon, 'Silicon Image Ultra-133 Medley ATA Raid
Controller' should displayed correctly under 'Device' and 'Driver' tab.
2. To view information about the devices attached to the controller, use the SiICfg
Utility and click on the device from the list.
Wie heeft hier ervaring mee?? kan ik er vanuitgaan dat de hd's blijven bestaan en van data voorzien blijven? en moet ik beide hd's op 1 poort aansluiten (primair) of de 2 hd's op beide poorten aansluiten (primair en secundair).. gaarne jullie reactie
robbie32
Ik heb een ide raid controllertje aangeschaft. Ik wil hier 2 x 250 gb hd's op aansluiten
in raid 1 (mirror). Nu lees ik verschillende verhalen dat de info van de harddisk verwijderd wordt indien deze aangesloten worden en de harde schijven gemount worden.
In de handleiding echter staat een stuk over het installeren van de raid controller op een reeds geinstalleerd systeem. Hierin staat niets over data verlies oid.
dit is het stuk uit de handleiding:
Silicon Image Ultra-133 Medley ATA Raid Controller OS Driver Installation
-------------------------------------------------------------------------
---------------------------------------------------------------------------
3)Adding the SiI RAID controller to an existing Windows 2000/XP installation
---------------------------------------------------------------------------
Follow the instructions in this section to install the Silicon Image
SiI 680 driver on a system already running Windows 2000.
1. Power off the system. Connect the hard drives to the PCI-680
controller and insert the controller into a PCI slot. Power up
the system.
2. During OS boot up, Windows 2000 will display the
'Found New Hardware Wizard'. Click 'Next'.
3. Select 'Search for a suitable driver for my device
(Recommended)' and Click 'Next'.
4. Under 'Optional search locations' insure that 'Floppy disk drives'
is checked.
5. Insert the diskette labeled ' Silicon Image Ultra-133 Medley ATA Raid Driver
Installation Disk' into A: and click 'Next'.
6. When the wizard indicates that it found a driver for the device click
'Next'.
7. If the 'Digital Signature Not Found' dialog appears, click 'Yes' to
continue installing the driver.
8. The wizard will now copy the required files to the system and start the
driver. After starting the driver the wizard will display a completion
dialog, click 'Finish' to exit the wizard.
9. See instructions in section 4 to verify controller was installed
correctly.
------------------------------------------------------------------
4) Verifying controller installation under Windows NT, 2000 and XP
------------------------------------------------------------------
Follow the instructions in this section to verify that the controller was
installed correctly.
For Windows 2000/XP
1. Right click on 'My Computer' icon, select 'Properties',
left click on 'Hardware' tab, and then on 'Device Manager'
button.
2. Double click on 'SCSI and RAID Controllers', If there is no
yellow '! ' or ' ? ' in front of
'Silicon Image Ultra-133 Medley ATA Raid Controller', the driver
is started correctly.
3. To view information about the devices attached to the controller, use the SiICfg
Utility and click on the device from the list.
For Windows NT 4.0
1. Double click on 'My Computer' icon, select 'Control Panel', click
on 'SCSI Adapters' icon, 'Silicon Image Ultra-133 Medley ATA Raid
Controller' should displayed correctly under 'Device' and 'Driver' tab.
2. To view information about the devices attached to the controller, use the SiICfg
Utility and click on the device from the list.
Wie heeft hier ervaring mee?? kan ik er vanuitgaan dat de hd's blijven bestaan en van data voorzien blijven? en moet ik beide hd's op 1 poort aansluiten (primair) of de 2 hd's op beide poorten aansluiten (primair en secundair).. gaarne jullie reactie
robbie32
